Download Drilling Problems - Directional Drilling Club PDF

TitleDrilling Problems - Directional Drilling Club
File Size58.2 KB
Total Pages5
Table of Contents
                            Drilling Problems - directional drilling club
                        
Document Text Contents
Page 1

Drilling Problems - directional drilling club

http://sites.google.com/site/directionaldrillingclub/6-drilling-problems[02-02-2012 23:17:41]

directional drilling club

Drilling Problems

There are many operational decisions made between the directional driller and the operator’s representative. To cover all
aspects of these considerations would be a book in itself. As with any drilling operation, the most important item on a
directional well is TEAM COOPERATION. The biggest hurtle to overcome in any multi-disciplined operation is the egos
that come together on-site. It is this human characteristic that if not properly controlled or utilized in a positive manner
can be the downfall on a directional project. Many oil field workers are very good working with equipment and getting the
job down but have a difficult time dealing with the various personalities on-site. Sometimes the school of hard knocks
becomes a tough learning environment known as “Employment Survival – 101”. A group of team players that share their
knowledge, communicate well and mutually arrive at the best solution will always produce the record well.
In order to address some of the operational considerations that directional company representatives must consider, the
following sections are prepared to address what affects the equipment and performance of a directional operation or
what could go wrong. These items may be discussed in the field with the operator’s representative and it is important to
realize the impact. As technologies are developed so will the potential problem areas increase.


Rig Mud Pumps


Too small of a mud pump can restrict the performance of the PDM and drilling rate. The PDM has an optimum flow rate
operating range. Insufficient available flow rate due to pressure restrictions and/or liner sizing can result in poor hole
cleaning in high angle wells. The pressure restrictions can also affect the MWD system utilized. As discussed earlier the
negative pulse system requires a pressure differential between the MWD and bit of 4000 KPa. If smaller nozzles are
required in the bit but the pump cannot handle the pressure the MWD system may not work or you may have to cycle
the pumps more often just to get a signal. This can lead to hole washes and lost time.

Duplex pumps produce more noise than a triplex pump and it can be very difficult to filter these noise out with an MWD
system to allow decoding of the pulses received on surface.

A low pre-charge can also decrease the efficiency of decoding pulse signals.


Solids Control Equipment

This is a key area that affects all equipment performance. Poor solids control can plug up MWD systems, create
aggressive wear on all equipment, reduce penetration rates, create potential downhole sticking situations and increase
formation damage.
In many cases poor solids control affects the mud properties and limits its ability to suspend solids. We have witnessed
cases where circulation of the drill string after running to bottom was impossible because the solids settled out in the
motor causing it to pack off.
On horizontal wells drill solids are pulverized into smaller particles due to a grinding action. If the best attempt to remove
solids is not made on the first circulation, these fine solids are left in the system and tend to increase formation plugging.


Rotary Equipment


When directionally drilling, it is imperative that all rotary equipment is in good condition. When table locks do not work it
is extremely difficult to control the tool-face when slide drilling. Wrapping tugger lines around the kelly bushing to control
tool-face is a very dangerous situation.

Introduction
pic 1.bmp
pic 2.bmp
pic 3.bmp

Contact Us
Deflecting a
wellbore
Directional Well
Downhole Mud
Motors

pic 4.bmp
pic 5.bmp
pic 6.bmp
pic 7.bmp

Downloads
571.jpg
9.1 Presentations
9.2 Presentations
9.3 Drilling
Applications
9.4 FEKETE
9.5 HRH WINLOG
down.banner.jpg
Drilling Full Course
Failure Analyisis
pic 13.bmp
program license
Well Engineering &
Construction for
Hussain Rabia

Drilling
Economics
Drilling Equipment
Drilling Problems
Horizontal Well

pic 10.JPG
pic 11.bmp
pic 12.JPG
pic 8.bmp
pic 9.JPG

References
STEEL
Sitemap

Search this site

MBA Oil &
Gas Degree
(UK)
Improve your
career w/ AMBA
MBA Apply now
for full-time and
online
www.RGU.ac.uk/MBA

Horizontal
Drilling
Latest news,

Tarus Gundrills Deephole drill at compound angles w/ Rotary Tables and Tilting Slides www.tarus.com
JM Petroleum Machinery Oil and Gas Equipments Manufacturer and Distributor www.jmpetroleum.com
couplings & joints Professional China manufacturer. Meticulous design of couplings www.jsgmic.com/en_index.html

http://sites.google.com/site/directionaldrillingclub/
http://sites.google.com/site/directionaldrillingclub/home
http://sites.google.com/site/directionaldrillingclub/home/pic%201.bmp
http://sites.google.com/site/directionaldrillingclub/home/pic%202.bmp
http://sites.google.com/site/directionaldrillingclub/home/pic%203.bmp
http://sites.google.com/site/directionaldrillingclub/contact-us
http://sites.google.com/site/directionaldrillingclub/deflecting-a-wellbore
http://sites.google.com/site/directionaldrillingclub/deflecting-a-wellbore
http://sites.google.com/site/directionaldrillingclub/planning-a-directional-well-2
http://sites.google.com/site/directionaldrillingclub/downhole-mud-motors
http://sites.google.com/site/directionaldrillingclub/downhole-mud-motors
http://sites.google.com/site/directionaldrillingclub/downhole-mud-motors/pic%204.bmp
http://sites.google.com/site/directionaldrillingclub/downhole-mud-motors/pic%205.bmp
http://sites.google.com/site/directionaldrillingclub/downhole-mud-motors/pic%206.bmp
http://sites.google.com/site/directionaldrillingclub/downhole-mud-motors/pic%207.bmp
http://sites.google.com/site/directionaldrillingclub/downloads
http://sites.google.com/site/directionaldrillingclub/downloads/571.jpg
http://sites.google.com/site/directionaldrillingclub/downloads/presentations
http://sites.google.com/site/directionaldrillingclub/downloads/presentations2
http://sites.google.com/site/directionaldrillingclub/downloads/drilling-applications
http://sites.google.com/site/directionaldrillingclub/downloads/drilling-applications
http://sites.google.com/site/directionaldrillingclub/downloads/fekete
http://sites.google.com/site/directionaldrillingclub/downloads/hrh-winlog
http://sites.google.com/site/directionaldrillingclub/downloads/down.banner.jpg
http://sites.google.com/site/directionaldrillingclub/downloads/slb
http://sites.google.com/site/directionaldrillingclub/downloads/failure-analyisis
http://sites.google.com/site/directionaldrillingclub/downloads/pic%2013.bmp
http://sites.google.com/site/directionaldrillingclub/downloads/program-license
http://sites.google.com/site/directionaldrillingclub/downloads/well-engineering
http://sites.google.com/site/directionaldrillingclub/downloads/well-engineering
http://sites.google.com/site/directionaldrillingclub/downloads/well-engineering
http://sites.google.com/site/directionaldrillingclub/drilling-economics
http://sites.google.com/site/directionaldrillingclub/drilling-economics
http://sites.google.com/site/directionaldrillingclub/equipments
http://sites.google.com/site/directionaldrillingclub/planning-a-horizontal-well
http://sites.google.com/site/directionaldrillingclub/planning-a-horizontal-well/pic%2010.JPG
http://sites.google.com/site/directionaldrillingclub/planning-a-horizontal-well/pic%2011.bmp
http://sites.google.com/site/directionaldrillingclub/planning-a-horizontal-well/pic%2012.JPG
http://sites.google.com/site/directionaldrillingclub/planning-a-horizontal-well/pic%208.bmp
http://sites.google.com/site/directionaldrillingclub/planning-a-horizontal-well/pic%209.JPG
http://sites.google.com/site/directionaldrillingclub/references
http://sites.google.com/site/directionaldrillingclub/steel
http://sites.google.com/site/directionaldrillingclub/system/app/pages/sitemap/hierarchy
http://pagead2.googlesyndication.com/aclk?sa=l&ai=BrbAcqMsqT5W_I8qJiAegwOmwBf_O3dMBx7PB7w7NkdXSA6CkKBABGAEgp7quEygDOABQ2JWBufr_____AWDl0uaDvA6gAceQuf8DsgEQc2l0ZXMuZ29vZ2xlLmNvbboBCjEyMHg2MDBfYXPIAQHaAUhodHRwOi8vc2l0ZXMuZ29vZ2xlLmNvbS9zaXRlL2RpcmVjdGlvbmFsZHJpbGxpbmdjbHViLzYtZHJpbGxpbmctcHJvYmxlbXOAAgGoAwGwA7j92wvIAxfoAwzoA5MF9QMCAADE9QMAAEAQ&num=1&sig=AOD64_3o7PgpQeRsS1YOxS17bNNXl__4bA&client=ca-pub-1475760361155103&adurl=http://www.rgu.ac.uk/ABS/postgraduate/page.cfm%3Fpge%3D43760
http://pagead2.googlesyndication.com/aclk?sa=l&ai=BrbAcqMsqT5W_I8qJiAegwOmwBf_O3dMBx7PB7w7NkdXSA6CkKBABGAEgp7quEygDOABQ2JWBufr_____AWDl0uaDvA6gAceQuf8DsgEQc2l0ZXMuZ29vZ2xlLmNvbboBCjEyMHg2MDBfYXPIAQHaAUhodHRwOi8vc2l0ZXMuZ29vZ2xlLmNvbS9zaXRlL2RpcmVjdGlvbmFsZHJpbGxpbmdjbHViLzYtZHJpbGxpbmctcHJvYmxlbXOAAgGoAwGwA7j92wvIAxfoAwzoA5MF9QMCAADE9QMAAEAQ&num=1&sig=AOD64_3o7PgpQeRsS1YOxS17bNNXl__4bA&client=ca-pub-1475760361155103&adurl=http://www.rgu.ac.uk/ABS/postgraduate/page.cfm%3Fpge%3D43760
http://pagead2.googlesyndication.com/aclk?sa=l&ai=BrbAcqMsqT5W_I8qJiAegwOmwBf_O3dMBx7PB7w7NkdXSA6CkKBABGAEgp7quEygDOABQ2JWBufr_____AWDl0uaDvA6gAceQuf8DsgEQc2l0ZXMuZ29vZ2xlLmNvbboBCjEyMHg2MDBfYXPIAQHaAUhodHRwOi8vc2l0ZXMuZ29vZ2xlLmNvbS9zaXRlL2RpcmVjdGlvbmFsZHJpbGxpbmdjbHViLzYtZHJpbGxpbmctcHJvYmxlbXOAAgGoAwGwA7j92wvIAxfoAwzoA5MF9QMCAADE9QMAAEAQ&num=1&sig=AOD64_3o7PgpQeRsS1YOxS17bNNXl__4bA&client=ca-pub-1475760361155103&adurl=http://www.rgu.ac.uk/ABS/postgraduate/page.cfm%3Fpge%3D43760
http://pagead2.googlesyndication.com/aclk?sa=l&ai=Bs2PnqMsqT5W_I8qJiAegwOmwBYTvk4UCxMmnpyKwqI6lIKDgFBACGAIgp7quEygDOABQtMy4l_______AWDl0uaDvA6gAZCajf8DsgEQc2l0ZXMuZ29vZ2xlLmNvbboBCjEyMHg2MDBfYXPIAQHaAUhodHRwOi8vc2l0ZXMuZ29vZ2xlLmNvbS9zaXRlL2RpcmVjdGlvbmFsZHJpbGxpbmdjbHViLzYtZHJpbGxpbmctcHJvYmxlbXOAAgGpAtla08PmGLY-qAMBsAO4_dsLyAMX6AMM6AOTBfUDAgAAxPUDAABAEA&num=2&sig=AOD64_0l5ZW4zkSIkDYtolkW6F4LPI3WtA&client=ca-pub-1475760361155103&adurl=http://www.nodig-construction.com/index.cfm%3Fcmd%3Dsearch%26objectSearchParam%3Ddrilling
http://pagead2.googlesyndication.com/aclk?sa=l&ai=Bs2PnqMsqT5W_I8qJiAegwOmwBYTvk4UCxMmnpyKwqI6lIKDgFBACGAIgp7quEygDOABQtMy4l_______AWDl0uaDvA6gAZCajf8DsgEQc2l0ZXMuZ29vZ2xlLmNvbboBCjEyMHg2MDBfYXPIAQHaAUhodHRwOi8vc2l0ZXMuZ29vZ2xlLmNvbS9zaXRlL2RpcmVjdGlvbmFsZHJpbGxpbmdjbHViLzYtZHJpbGxpbmctcHJvYmxlbXOAAgGpAtla08PmGLY-qAMBsAO4_dsLyAMX6AMM6AOTBfUDAgAAxPUDAABAEA&num=2&sig=AOD64_0l5ZW4zkSIkDYtolkW6F4LPI3WtA&client=ca-pub-1475760361155103&adurl=http://www.nodig-construction.com/index.cfm%3Fcmd%3Dsearch%26objectSearchParam%3Ddrilling
http://www.google.com/url?ct=abg&q=https://www.google.com/adsense/support/bin/request.py%3Fcontact%3Dabg_afc%26url%3Dhttp://sites.google.com/site/directionaldrillingclub/6-drilling-problems%26hl%3Den%26client%3Dca-pub-1475760361155103%26adU%3Dwww.RGU.ac.uk/MBA%26adT%3DMBA%2BOil%2B%2526amp%253B%2BGas%2BDegree%2B(UK)%26adU%3Dwww.nodig-construction.com%26adT%3DHorizontal%2BDrilling%26adU%3Dwww.redpathmining.com%26adT%3DRedpath%2BRaiseboring%26gl%3DIN&usg=AFQjCNG4LAW9Gm83UdYkAC108zcU8Jj8VQ
http://pagead2.googlesyndication.com/aclk?sa=L&ai=BiYRvqMsqT_-rLuaKiAeCudywBbvy0DezjPqPAcCNtwGQ5SIQARgBIKe6rhMoAzgAUI3Qv3Zg5dLmg7wOsgEQc2l0ZXMuZ29vZ2xlLmNvbboBCTcyOHg5MF9hc8gBAdoBSGh0dHA6Ly9zaXRlcy5nb29nbGUuY29tL3NpdGUvZGlyZWN0aW9uYWxkcmlsbGluZ2NsdWIvNi1kcmlsbGluZy1wcm9ibGVtc-ABAqgDAbADuP3bC8gDF-gDDOgDkwX1AwIAAMD1AwAAQBA&num=1&sig=AOD64_2VRvHz0strkZX0c7nbX68YMv_UvA&client=ca-pub-1475760361155103&adurl=http://www.tarus.com/products/index.php%3Fsource%3Dgoogle
http://pagead2.googlesyndication.com/aclk?sa=L&ai=BRLQnqMsqT_-rLuaKiAeCudywBaDbo-0BgPjUrx3AjbcBwO0aEAIYAiCnuq4TKAM4AFCTisqF-v____8BYOXS5oO8DrIBEHNpdGVzLmdvb2dsZS5jb226AQk3Mjh4OTBfYXPIAQHaAUhodHRwOi8vc2l0ZXMuZ29vZ2xlLmNvbS9zaXRlL2RpcmVjdGlvbmFsZHJpbGxpbmdjbHViLzYtZHJpbGxpbmctcHJvYmxlbXPgAQKpApGl0FlZ7Ko-qAMBsAO4_dsLyAMX6AMM6AOTBfUDAgAAwPUDAABAEA&num=2&sig=AOD64_3ioAsNAq0vSQHy6VyGG5nFe-qbpg&client=ca-pub-1475760361155103&adurl=http://www.jmpetroleum.com
http://pagead2.googlesyndication.com/aclk?sa=L&ai=BnRH5qMsqT_-rLuaKiAeCudywBaCojPUCsK-29kvAjbcBoMuYARADGAMgp7quEygDOABQ5JLs4_j_____AWDl0uaDvA6yARBzaXRlcy5nb29nbGUuY29tugEJNzI4eDkwX2FzyAEB2gFIaHR0cDovL3NpdGVzLmdvb2dsZS5jb20vc2l0ZS9kaXJlY3Rpb25hbGRyaWxsaW5nY2x1Yi82LWRyaWxsaW5nLXByb2JsZW1z4AECgAIBqQLdY5VwXkyFPsgCqJXVLKgDAbADuP3bC8gDF-gDDOgDkwX1AwIAAMD1AwAAQBA&num=3&sig=AOD64_30na7P_lC3-R0WUBJUqcaySxOA3w&client=ca-pub-1475760361155103&adurl=http://www.jsgmic.com/coupling/&nm=1
http://www.google.com/url?ct=abg&q=https://www.google.com/adsense/support/bin/request.py%3Fcontact%3Dabg_afc%26url%3Dhttp://sites.google.com/site/directionaldrillingclub/6-drilling-problems%26hl%3Den%26client%3Dca-pub-1475760361155103%26adU%3Dwww.tarus.com%26adT%3DTarus%2BGundrills%26adU%3Dwww.jmpetroleum.com%26adT%3DJM%2BPetroleum%2BMachinery%26adU%3Dwww.jsgmic.com/en_index.html%26adT%3Dcouplings%2B%2526amp%253B%2Bjoints%26gl%3DIN&usg=AFQjCNF3b0VmWm5QJ15RSeJN_gkJh4HU9A

Page 2

Drilling Problems - directional drilling club

http://sites.google.com/site/directionaldrillingclub/6-drilling-problems[02-02-2012 23:17:41]


Tong lines that are out of calibration can result in incorrect torque applied to critical connections that may result in motors
backing off downhole.

Automatic diggers that do not allow subtle increases in WOB can result in motors frequently stalling when trying to
initiate drilling after each connection. This affects the average ROP and time spent drilling.

Smaller diameter drill pipe will twist more due to torque than larger diameter. Single shot operations with 3 ½” drill pipe
can become very difficult if not impossible as the depth increase beyond 500m (1500 feet).

Insufficient hevi-wate drill pipe will quickly limit the depth you can drill to and still make any slide corrections.

Drilling vertical hole to KOP with too small of drill collars can result in having to pick-up directional tools earlier than
planned due to deviation.


Grounding Of Electrical Equipment

All MWD systems use computers and special algorithms to decode pulse or electromagnetic signals. In some cases
poorly grounded light plants and generators have created sufficient interference to prevent clear reception of these
signals. In some cases the signal noise is too large to filter out.


Communication and Data Collection Equipment

Although an extra cost to the job, a phone system between the drill floor and the command center can save
considerable time and relay drilling concerns much quicker. Remote recording instruments that provide all drilling data to
the command center also allows a more educated decision when drilling problems arise. They also allow others to
review the overall operation from a different point of view than the driller. In some cases small pressure fluctuations
noted on the standpipe pressure graph was all that indicated a failing bit. The performance trends are much easier to
detect when a graphical display is available.


Bit Selection and Life


Although PDC bits have come a long way in their development they still have some restrictions in their directional
applications. A very careful review of the formations being drilled through, especially in the build section, must be made.
Their use in horizontal sections has seen dramatic improvement over the years. It is very important the correct motor be
selected for these runs otherwise their design cannot be fully utilized.

When building inclination or trying to turn the wellbore, the outer row of teeth on the bit has the biggest influence. When
erratic build or turn rates are noted, or you can’t build or drop inclination, it may be the teeth are worn down too far to
“get a good bite” on the formation.
The effective life of bits used on directional wells is usually lower than normal due to the different loading applied to the
bit. Remember when rotary drilling with a motor to add the table RPM to the motor RPM and select the bit based upon
this.


Motor Problems

High temperature holes (greater than 100o C) can severely limit the performance life of motors. The temperature tends to
cause the elastomer in the stators to swell and cause premature stalling.
Hydrocarbon based drilling fluids can cause the stator lining to swell, loose strength and chunk out.

Abrasive fine solids left in the drilling fluid may cause aggressive wear of the stator that will result in loss of power and
reduced ROP.
Excessive back reaming can cause motor connections to back-off.

Rotating motors at RPM’s greater than 50 is very hard on the bearing and drive sections. Also rotating motors with
adjustable housing settings greater than 1.8o can cause premature bearing failures.

When drilling underbalanced the motor is typically not lubricated to the same degree as overbalanced wells.
Consequently, some very strange wear patterns have been seen on these motors and they may not last as long.

Unique “pressuring up” situations have been noted on small hole size (121mm) underbalanced wells. Not fully
understood at this time but appears to be pressure and temperature related. Motors have pressured up within 12 hours

techniques,
videos, jobsites,
books,
community
www.nodig-construction…

Redpath
Raiseboring
Manufacturing,
sales, service.
Global Expertise.
www.redpathmining.com

http://pagead2.googlesyndication.com/aclk?sa=L&ai=B8wFzqMsqT5W_I8qJiAegwOmwBZOxnOYCu8Okh0LAjbcBgPkrEAMYAyCnuq4TKAM4AFDAmLGY_f____8BYOXS5oO8DrIBEHNpdGVzLmdvb2dsZS5jb226AQoxMjB4NjAwX2FzyAEB2gFIaHR0cDovL3NpdGVzLmdvb2dsZS5jb20vc2l0ZS9kaXJlY3Rpb25hbGRyaWxsaW5nY2x1Yi82LWRyaWxsaW5nLXByb2JsZW1zqQJGoZdV3tCwPqgDAbADuP3bC8gDF-gDDOgDkwX1AwIAAMT1AwAAQBA&num=3&sig=AOD64_1Dy2nDIEun-jWdvr8l0AgFHtAomg&client=ca-pub-1475760361155103&adurl=http://www.redpathmining.com/services/raiseboring/
http://pagead2.googlesyndication.com/aclk?sa=L&ai=B8wFzqMsqT5W_I8qJiAegwOmwBZOxnOYCu8Okh0LAjbcBgPkrEAMYAyCnuq4TKAM4AFDAmLGY_f____8BYOXS5oO8DrIBEHNpdGVzLmdvb2dsZS5jb226AQoxMjB4NjAwX2FzyAEB2gFIaHR0cDovL3NpdGVzLmdvb2dsZS5jb20vc2l0ZS9kaXJlY3Rpb25hbGRyaWxsaW5nY2x1Yi82LWRyaWxsaW5nLXByb2JsZW1zqQJGoZdV3tCwPqgDAbADuP3bC8gDF-gDDOgDkwX1AwIAAMT1AwAAQBA&num=3&sig=AOD64_1Dy2nDIEun-jWdvr8l0AgFHtAomg&client=ca-pub-1475760361155103&adurl=http://www.redpathmining.com/services/raiseboring/

Page 3

Drilling Problems - directional drilling club

http://sites.google.com/site/directionaldrillingclub/6-drilling-problems[02-02-2012 23:17:41]

of drilling but show no problems on surface when disassembled.

Stators are vary susceptible to aggressive wear on underbalanced wells with solids contents greater than 5%. Some
motors only lasted 12 hours.


MWD Systems

Most are susceptible to solids plugging and have a flow rate limit through the MWD NMDC.

Most have a percent solids limit that they can function in.

Not all systems can handle lubra beads (or similar additives) before plugging.

Each type of system has its own limit to the type and concentration of lost circulation material before plugging. It is
always better to discuss with directional company the potential of lost circulation and possible mud additives that may be
added.
Jarring with MWD systems in the hole can result in damaging the electronic components. If hole problems are a
significant problem in the area consider a retrievable system. The only problem here is most retrievable systems have a
lower reliability value (mean time between failure).

On whipstock operations never mill out casing with an MWD system in the drill string. Excessive damage occurs to the
MWD system that the operator will be required to pay for.

Pumping acid or bleach through MWD systems prior to tripping out at the end of a well can be very damaging to the
equipment. In some cases operators have had to buy complete strings of tubulars due to internal cracking and probe
damage just because they didn’t want to make another trip to flush the hole.

A unique problem noted with electromagnetic systems is the interference between two rigs working close together. In
one case the rigs were 50m apart and each rig could read the signal from the other. There are methods in place to
avoid this occurrence.

Most electromagnetic systems require some conductive fluid in the wellbore. In some cases the entire signal has been
lost when drilling with diesel due to its poor conductivity.

Most standard electromagnetic systems have a limit to the depth they can drill to due to the resistivity of the formations
between the bit and surface. Resistivity logs must be carefully reviewed and modeled before selecting this tool for
service.

Failure of Z-axis accelerometer results in incorrect inclination measurements. The variation of these values is very subtle
in a horizontal well and must be closely monitored at all times but especially when there are TVD concerns. Most times
when the value remains the same for three surveys the tool should be pulled and checked.


Build Sections


Typically a directional driller will try to get kicked off slightly above the planned point. They should never get to far above
the line unless there is a long tangent or hold section to the target. On build and turn profiles for a horizontal well, the
driller should try to stay on the line as much as possible since getting behind or to far ahead can result in sharp doglegs
later in the well path.
If the current motor setting is not achieving the desired build rate do not wait too long before tripping to change the
setting. Unless the area build performance is very well known waiting too long can result in missing the target or sharp
doglegs.


Large hole sizes (greater than 311mm) that require high build rates (greater than 3 o/30m in some cases) may be drilled
faster with a smaller assembly and then opened up. This is especially true for deviated surface hole where the
formations are too unconsolidated to achieve the build rates.

On long reach wells with the build section left open, it is prudent to make a couple of wiper trips (maybe a reamer trip)
through the build section to smooth out any ledges. This will reduce the hole torque and drag values as the hold section
continues to be drilled.

Never ream a build section without MWD equipment since this is when most new holes are started. Always orient
through the build section with a reaming assembly, watching the tool-face behaviour.


Hold Sections

Page 4

Drilling Problems - directional drilling club

http://sites.google.com/site/directionaldrillingclub/6-drilling-problems[02-02-2012 23:17:41]

Depending upon the inclination this is when correction for azimuth is very important. The first 60m of hole drilled should
be surveyed every 10m (single) to ensure the hole is maintaining the desired path.

Some operators have released the directional company too early in these sections and when trying to makeup some
time they apply too much WOB and push the wellpath off target.

Stabilized bottomhole assemblies work well in this section but will require reaming all the way to bottom since the
directional assembly typically drills a smaller average hole size.
Frequent wiper trips or pumping viscous mud sweeps are highly recommended when the hold section inclination is greater than 60
degrees.


Horizontal Sections


Most common problem in the horizontal section is getting too aggressive in changing the TVD. Abrupt changes may get
you back into the zone quicker but can limit the horizontal length. In some cases when requested to climb in TVD very
quickly the directional driller was unable to come back down and level off in the zone.
Know the hard boundaries in TVD before attempting any TVD changes. Determine what could happen to the well
productivity if it suddenly climbs too high or drops too low.

Beds of cuttings typically build up in the horizontal section like sand dunes. This can be noticed if the drag or torque
begins to increase over what a torque/drag program predicts. Routine short wiper trips to stir up these beds helps clean
the hole and prevent sticking.
Never make quick changes in inclination or azimuth at the heel of a horizontal well, as this will quickly limit the maximum
length you can drill.


Open Hole Sidetracks

Biggest mistake made in this operation is pushing too hard and fast. It is imperative a good ledge is built before
increasing the differential pressure on the motor. Do not rush the directional driller and have him drill faster once a ledge
is built.
Never test the ledge by placing weight onto it. This is the quickest way to break off the ledge. Once a good ledge is
established slowly increase weight on bit in stages and drill by differential pressure (control drill).
Use densified cement plugs whenever possible when planning to sidetrack a well off of cement. Remember the bit will
take the path of least resistance so if the cement is softer than the formation the bit will drill up the cement.
Plan to have at least 75m of hard cement below sidetrack point.
When entering a sidetracked leg always orient through to minimize the chance of breaking off ledges or starting a new
hole.
Have a sidetrack plan in place and stick to it. Allow the directional driller to show his experience at telling when a good
sidetrack has been created.


Whipstocks

Biggest problem on these operations is getting the well started in the right direction. When there is angle in the well and
it has an established direction you can not just point the whipstock where you want to go. All drilling must be down by
tool-face.

When high build rates are required (greater than 20 o/30m) it is very easy to get behind the curve. Due to magnetic
interference and/or position of directional sensors you may have to drill 30 or 40m of hole before you know if you are
achieving the required build rates. If you only needed a change of 30 degrees you may already be behind the curve.

Always survey more often in the first 2 to 4 singles to check build rates (every meter in some cases) once the sensors
are in new hole.
Many times the whipstock is plus or minus 25 degrees from where you planned it to be.
Some whipstocks can fall in on themselves when set at tool-faces greater than 90 degrees left or right when the
inclination is greater than 45 degrees.


Magnetic Interference

Whether it is from hot tools, solar flare activity or proximity to steel this can be a very bothersome concern. It takes
requires careful attention by both the directional driller and the MWD operator to find these problems.

Solar activity has produced local magnetic declination errors of up to 7 degrees in the northern latitudes. Imagine what 7

Similer Documents